Home > Error Code > Western Digital Error Code 0007

Western Digital Error Code 0007

Contents

Re-Test Drive 104 Drive Not Ready The drive did not properly respond to test commands. Replace the drive if the error repeats. An interrupt command to perform a specific task failed to complete. Replace the drive if the error repeats. have a peek at this web-site

I used SeaTools (it was a Seagate drive) and had the same issue. Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer). Thanks. It also may be due to a defective connection. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Western Digital Error Code 0007

This may be due to a defect with the drive or a bad connection. I want a scorpio black zy, Nov 2, 2009 #12 Adrian Wong Da Boss Staff Member zy said: ↑ Well, I upgraded my RAM and Hard disk, so they have Several instances of track information could not be found. Replace the drive if the error repeats.

If the system cannot properly handle a drive running a specific Ultra ATA rate such as ATA100, the data may become corrupted. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Monitor the smart data to see if the drive is reporting more bad sectors or other problems over time. Replace Drive 227 SMART Not Supported Self-Monitoring, Analysis, and Reporting Technology (SMART) Certain older drives do not support SMART.

ViVard and GSmartControl for Quick/Extended/Conveyance tests came out clean and error-free. This may be due to a defect with the drive or a bad connection. Check cabling and retest. I had my WD delivered before 3-4 days.

Replace the drive. Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy

Tech Foulty connections? Re-Test Drive 116 IDNF Error Address Not Found Error.

Canon Ir3300 Error Code 0007

This may be due to a media error. https://community.wd.com/t/smart-error-help/8367 After that i tested my drive using Diagnostics from WD Smartware. Western Digital Error Code 0007 If the automatic repair feature is unable to repair these errors, replace the drive. What exactly was wrong with it?

Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests. Check This Out Check cabling and retest. Re-test 132 Command Error Command Aborted. Warranty from HDD manufacturer is 3 years.

Auto Offline Data Collection: Enabled. James Back to top #3 rotor123 rotor123 Moderator 8,008 posts OFFLINE Gender:Male Location:New Jersey Local time:06:53 PM Posted 09 January 2013 - 10:01 PM Hi anonanon (Roger), Good name, I It also may be due to a defective connection. Source The WD extended test completed in about an hour and produced this report, which doesn't tell me much: Test Option: EXTENDED TEST Model Number: WDC WD5001AALS-00E3A0 Unit Serial Number: WD-WCATR2850613 Firmware

As a guest, you can browse and view the various discussions in the forums, but can not create a new topic or reply to an existing one unless you are logged Replace the drive if the error repeats. Test complete Defect Free Now, can I assume that the hard drive is now fine, and more errors won't crop up in the future?

Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9.

Re-test Drive 220 Drive is Locked Security feature of the drive reports locked status. Re-test Drive 148 Not Selected Drive not selected. According to to western digital's site: 223 Errors Repaired Errors found, but have been repaired successfully. These are are the results I got.

I also just pop-in 320GB scorpio black, wow really felt the diff mikegas, Nov 2, 2009 #11 zy zynine.com Staff Member mikegas said: ↑ uh oh .. There were media errors that were within the repair capabilities of diagnostic utility. Version 4.12 for older drives and version 5.00 for current drives. have a peek here Track 0 on the drive must be accessed to perform parts of various internal tests.

Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. Total time to complete Offline data collection: ( 8400) seconds. Anything else I should try to salvage this drive? 10-03-2008, 08:38 PM #10 manic TSF Enthusiast Join Date: Aug 2005 Location: Florida Posts: 5,741 OS: xp Zeroing Replace Drive 581 Write Fault When either writing zeros or relocating a sector, the Write command failed.

Replace Drive 211 Self Test Never Completed The drives internal self-test could not complete due to unrepairable errors.